Auto Super-Service Center

Let me start by saying that your wheel bearings keep the wheels on your vehicle. Did that get your attention? In this article we’ll discuss more about wheel bearings and how you can keep them doing their very important job while you drive around Havana Florida.

Come see us at: 3781 N. Monroe St. Tallahassee, Florida 32303

Wheel bearings are pretty simple parts. They’re made of high quality steel and are engineered to last 100,000 miles or more if properly cared for. The bearings do two very important jobs: First they allow the wheel to freely rotate with as little friction as possible. Second, they support the weight of the vehicle. For example, if your car weighs 3,600 pounds, each wheel has to support approximately 900 pounds. That’s a lot of heavy lifting over many, many thousands of miles.

Even though wheel bearings are relatively simple, they need to be in near perfect condition to do their job. The bearings are packed with heavy grease to lubricate and protect them. A seal keeps the grease in and water and dirt out. It’s when the seal starts to leak that problems begin. The grease can become contaminated; causing the wheel bearings to overheat and ultimately fail.

The first sign that your wheel bearings are in trouble is an unusual noise coming from a wheel. It could be a chirping, growling, rumbling or a cyclic sound. The noise could get louder or even disappear at certain speeds. Your technician at Auto Super-Service Center can inspect for bearing wear by lifting the vehicle and checking for play in the wheel.

Now some wheel bearing assemblies are factory sealed. That means that they cannot be serviced – they can only be replaced. Those that aren’t sealed can be serviced on schedule. The bearings are removed, cleaned and inspected. If the bearings are still good, they’re re-installed – if not, they’re replaced. They are then packed in grease and a new seal is installed.

If your vehicle has a factory sealed wheel bearing assembly, the entire assembly needs to be replaced when trouble arises. Unfortunately, the parts are pretty pricy – but they usually last about 150,000 miles as long as the seals hold up.

Now, even a good seal cannot keep out water that’s exerting pressure on the seal. So if you’ve driven through hub deep water your bearings should be cleaned and repacked if they’re serviceable. If you have factory sealed bearings, you just need to watch for signs of premature failure.

If your wheel bearings can be serviced, your owner’s manual will recommend an interval, usually around 30,000 miles.

Now, if you have any sort of trailer, don’t forget its wheel bearings. They probably need to be serviced even more frequently. This is especially true for boat trailers that are used to launch the boat by backing it into the water. These should be serviced every year, usually at the end of the season so that the bearings don’t have the opportunity to sit and rust all winter.

So what happens if wheel bearings fail? Well, the wheel can literally fall off the vehicle. I don’t need to tell you how bad that could be. So check with your service advisor at Auto Super-Service Center and see if your vehicle’s wheel bearings can be serviced and when it’s recommended. Listen for warning signs. If you’ve been fording streams or puddle surfing after rainstorms, be especially vigilant.

Come by Auto Super-Service Center for a wheel bearing inspection, or for preventive maintenance. Call for an appointment at 850-562-4608

Tires do a lot of work. They transfer engine power and braking forces to the road; they handle steering control; and they cushion all those bumps and jolts. They also support the entire weight of the vehicle, including you and your passengers. With such critical work to do, you want your tires to do their job well. And since replacing tires is fairly expensive, you want them to last as long as possible.

There are three keys to long, even tire wear:

• Proper tire inflation
• Proper wheel alignment
• Regular tire rotation and balancing

The front tires on a car take the brunt of the steering forces. As they push through turns, the shoulders of the front tires wear down more quickly than the rear tires. Rotating front and rear tires allows them to all wear at about the same rate. That’s especially true of front wheel drive vehicles whose front tires steer, and put the power to the road.

SUVs and pick-ups, especially four wheel drives, also tend to wear their tires more unevenly than cars because of their suspension and drive train set-up. Your owner’s manual will likely contain a schedule for tire rotation. It’s usually every 5,000 miles or so.

Also, there are different rotation patterns for different vehicles. Auto Super-Service Center will know which is right for your vehicle. That brings us to wheel balancing. When wheels are balanced, they spin on the axel evenly. When they are out of balance, they wobble a bit. That makes the tires wear unevenly and may transmit a vibration to the car. Your service technician at Auto Super-Service Center puts weights on your wheels to balance them out so that they turn true and smooth.

Tires are a big investment for any vehicle. They’re critical for keeping you safely on the road. The cost for regular rotation and balancing is more than made up in extended tire life. And, can you really put a price on your safety and that of your passengers?

So you love our job, and your family life is great: You have achieved balance. But can you the same for your wheels? You can tell if your tires are out of balance by vibrations at higher speeds. If one of the front tires is out, you feel the vibration in the steering wheel. If it’s a back tire, you’ll feel the vibration in your seat.

Tires and wheels are pretty heavy. When a tire is mounted on a wheel, it is usually not perfectly balanced. So the tire technician will spin the tire on a machine to determine where it’s too heavy. He will then place weights on the wheels in strategic locations to balance it out. When a tire is out of balance, it actually bounces down the road instead of rolling smoothly. Since the average size tire rotates at about 850 revolutions per minute at 60 MPH, it is actually slamming into the pavement 14 times a second. That’s where you get your vibration.

Most people are surprised at how smoothly their car rides after balancing all four wheels.

Most high-quality tires hold their balance pretty well. They just get out of balance gradually with normal wear and tear. If you suddenly feel a vibration, it is probably because you lost a wheel balancing weight along the way. Definitely get a balance if you feel a vibration, change your rims or have a flat repaired. Putting off a needed balance job leads to excessive tire wear, wear to your shocks, struts, steering and suspension parts. wheel balancing not only improves your ride and handling, but also can save you some big repair bills and possibly an accident. Additionally, you will get better gas mileage.

Some people have their tires balanced at every rotation. Others do it every other time. Check your owners’ manual for your requirements, or ask your technician. Doing thus will put you on the path to mechanical wheel balance

.

What type of technology do you use? Do you prefer an 8-track tape or an iPod? When it comes to winter tires, much of the public’s perception dates back to when 8-track was the best way to listen to the Bee Gees.

Twenty years ago, winter tires differed from highway tires only in their tread design. We called them snow tires back then and they had big, knobby lugs that were designed to give good traction in deep snow. They had the same rubber compound as regular tires and they weren’t very good on ice, packed snow or wet roads. They were not even very good on dry roads. They really helped in deep or loose snow, but they did a poor job the rest of the time. They were loud and rode hard. You couldn’t wait to get them off in the spring.

Then all-season tires started to come along. All-season tires are really a compromise between summer and winter performance. They have acceptable hot weather ride and tread life, and you can get through mild winter road conditions OK. But there are some really good reasons to consider winter tires.

Modern winter tires do a terrific job in a wide range of winter conditions. First of all, below 45 degrees Fahrenheit, regular tires become hard and inflexible. That means they don’t provide the road grip you need. Even if you don’t live somewhere with a lot of snow, but it still gets below 45 degrees in the winter, you will be safer with winter tires.

In addition, they are specifically designed to more effectively move snow and water. That’s the key to traction on ice, packed snow and wet roads. They use a micro-pore compound that allows the tire to bite into ice and snow. They also use wider grooves that run around the circumference of the tread to expel snow from the tire better. The lugs and grooves on winter tires have a special shape that throws the packed snow out of the tread as the tire turns. The tread is then open when it comes back in contact with the road and can provide good traction.

Winter tires also have a lot of sipes. Sipes are thin slits in the tread. The edge of the sipes grab ice and packed snow to provide tons of traction and to expel water and slush out of the tread. winter tires have a rounder casing to cut into the snow’s surface. The treads on regular summer tires can actually get packed with snow instead and become very slick. winter tires offer 25% to 50% more traction than all-season tires. And when it comes to stopping power, all-season tires take 42% longer to stop than winter tires. Sometimes that’s the difference between getting home safely and spending the night in a snow bank.

Now back when the 8-track was king, you just put snow tires on the drive wheels. That worked out OK because the rubber compound was essentially the same. Now, winter tires provide so much more traction than all-season or summer tires, that there’s a huge difference between the traction at the front and rear ends of the car if you only put winter tires on the drive wheels.

For example: if you take a corner on an icy road and the rear end starts to slide out, essentially the rear is trying to pass the front because it’s going faster. If you have high traction winter tires only on the front, they are going to be much more effective at transferring cornering grip and stopping power to the front wheels. This will actually cause the rear end to whip out even more.

That’s why tire manufactures instruct their dealers that they must install winter tires on the rear wheels as well whenever they put winter tires on the front end of any vehicle. It’s a major safety concern. It’s strongly recommended that winter tires be installed on all four wheels on rear wheel drive vehicles as well. The front tires do most of the steering and braking work – it only makes sense that you provide the front end with the best traction you can.

People often assume that if they have four-wheel drive or all-wheel drive they don’t need winter tires on all four wheels. Would you intentionally disconnect the four-wheel drive in poor road conditions? Of course you wouldn’t, but that’s essentially what you do if you only put winter tires on one end. It only makes sense to have the same level of traction and control at all four corners.

The province of Quebec in Canada has issued a law requiring all passenger vehicles, taxis and rental cars with Quebec license plates to install a full set of four winter tires between November 15th and April 1. It’s that important.

Many modern cars have traction control and anti-lock brakes so people may think that they don’t need winter tires. But you need traction to accelerate, steer and stop. The tires provide the traction so that the traction control and anti-lock brakes have something to work with.

Look for tires with the symbol of a mountain with a snowflake in it. This means the tire complies with the severe snow standard. All-season tires will have an M&S, for mud and snow, on the sidewall.

So when the temperatures drop below 45 degrees, be sure you have a set of four winter tires for maximum performance in snow, packed snow, ice, wet and dry roads. Your tire professional can help you find the right winter tire for your vehicle and driving needs.

So, when are your tires actually worn out? This is a question a lot of us in Tallahassee Florida ask ourselves. For many, the answer is ‘when they no longer pass a safety inspection’. But waiting that long can have a serious impact on your safety.

The U.S. Federal government doesn’t have any laws for tread depth, but 42 of the states, and all of Canada, do have regulations. They consider two-thirty-seconds of an inch to be the minimum legal tread depth. Two other states, including California, consider one-thirty-second to be the minimum and six states have no standards at all. Call us at Auto Super-Service Center (just call 850-562-4608) to find out what your requirements are in the Tallahassee Florida area.

Since 1968, U.S. law has required that a raised bar be molded across all tires. When tires are worn enough that this bar becomes visible, there’s just 2/32” of tread left. But does that older standard give you enough safety?

Well, Consumer Reports issued a call to consider replacing tires when tread reaches 4/32”. And the recommendation is backed by some very compelling studies. Now before we go into the studies, you need to know that the big issue is braking on wet surfaces.

We tend to think of the brakes doing all the stopping, but you also need to have effective tires to actually stop the car. When it’s wet or snowy in Tallahassee Florida, the tread of the tire is critical to stopping power.

Picture this: you’re driving over a water-covered stretch of road. Your tires actually need to be in contact with the road in order to stop. That means the tire has to channel the water away so the tire is actually contacting the road and not floating on a thin film of water – a condition known as hydroplaning. When there’s not enough tread depth on a tire, it can’t move the water out of the way and you start to hydroplane.

This is where the studies come in. We think you’ll be surprised. A section of a test track was flooded with a thin layer of water. If you laid a dime flat on the track, the water would be deep enough to surround the coin, but not enough to cover it.

A car and a full-sized pick-up truck were brought up to 70 mph and then made a hard stop in the wet test area. Stopping distance and time were measured for three different tire depths. First, they tested new tires. Then tires worn to legal limits. And finally, tires with 4/32” of tread were tested – this is the depth suggested by Consumer Reports

When the car with the legally worn tires had braked for the distance required to stop the car with new tires, it was still going 55 mph. The stopping distance was nearly doubled. That means if you barely have room to stop with new tires, then you would hit the car in front of you at 55 mph with the worn tires.

Now with the partially worn tires – at the depth recommended by Consumer Reports – the car was still going at 45 mph at the point where new tires brought the car to a halt. That’s a big improvement – you can see why Consumer Reports and others are calling for a new standard.

Now without going into all the details, let us tell you that stopping the truck with worn tires needed almost 1/10 of a mile of clear road ahead to come to a safe stop. Obviously this is really a big safety issue.

The tests were conducted with the same vehicles, but with different sets of tires. The brakes were the same, so the only variable, was the tires.

So, how do you know when your tires are at 4/32”? Well, it’s pretty easy. Just insert a quarter into the tread. Put it in upside down. If the tread doesn’t cover George Washington’s hairline, it’s time to replace your tires. With a Canadian quarter, the tread should cover the numbers in the year stamp.

Now you may remember doing that with pennies. But a penny gives you 2/32” of an inch to Abraham Lincoln’s head. The quarter is the new standard – 4/32”.

Tires are a big ticket item and most people in Tallahassee Florida want to get the most wear out of them that they can. But do you want that much more risk just to run your tires until they are legally worn out? For us, and we would guess for many, the answer is “no”.

Well, Mr. Washington, let’s go out and look at my tires.

Auto Super-Service Center
3781 N. Monroe St.
Tallahassee, Florida 32303
850-562-4608

It seems like everywhere you go around Tallahassee you see custom wheels. Big trucks, little cars, mini-vans – it doesn’t matter, people are expressing themselves with custom wheels. Some people want smaller tires and wheels – some want larger – and some want them enormous. So where do you start if you want new wheels? We suggest you start with your budget. We know, that sounds so practical. But if the look you’re after goes beyond just new tires and wheels and enters into the world of suspension modifications, you need to be prepared for the additional cost.

Let’s start with something easy – you want to give your ride a unique look and the stock wheel size is just right for you. One of the concerns you will have is that the new wheels have the same offset as your factory wheels.

First, what is offset? The wheel bolts onto the hub on the car’s axel. The distance from the inside edge of the wheel to the point at which it bolts on, is the offset. If the new wheel has a different offset from the factory, the tires may rub on the inside or outside of the wheel well. That could lead to catastrophic tire failure.

Your Tallahassee tire and wheel professional can help you find the right size wheel – or install adapters to make your new wheels fit. All you have to do is pick from the hundreds of styles available.

So, what if you want to upsize? Well, if it is just bigger wheels you want, but you want to keep the same overall tire diameter, that’s pretty easy. The same offset concerns apply. You need to know that the tires will likely be a little bit wider than the originals and could rub when you make sharp turns. A tire professional at Auto Super-Service Center can help you avoid this.

It is also important to keep the same overall tire diameter because changing the rolling diameter can mess with your anti-lock brakes and stability control systems. Are you starting to see why you want to consult with a tire and wheel expert? Is “super-size me” your motto? If it is, you are going to have to lift your vehicle to make room for those huge tires. A mild lift doesn’t require extensive modifications. An extreme lift means a lot of new hardware under the vehicle. It also means a lot of stock electronic systems need to be recalibrated to the new tire size. For example, your speedometer and odometer will give false readings if they aren’t recalibrated.

You should also be aware of possible performance issues. Bigger tires and wheels weigh more. Experts refer to this as unsprung weight because it isn’t held up by your suspension system. Increased unsprung weight affects performance in different ways than an equivalent amount of groceries or little soccer players in the passenger compartment. Acceleration is negatively affected. Stopping distances may also be increased – sometimes dramatically. If you want really big tires and wheels, you might need to upgrade your brakes to compensate.

Heading the other direction, some folks like to run smaller than standard wheels and lower the suspension. All of the same fitment issues still apply as well as calibration issues. Don’t think that suspension modifications are a bad thing. Many systems actually improve ride, function and performance over the stock set-up.

Regardless of your budget, you want your vehicle to continue to do all the things you need it to do. Some of those show cars and trucks you see on TV look fantastic, but have been modified in ways that may not suit your needs. For example, if you put large rims on your SUV with low profile tires, you may be in for busted rims if you go off-roading a lot. There just isn’t enough sidewall to absorb the impact of thumping over rocks.

Some people stuff the largest tires and wheels possible in their vehicles but have to severely restrict suspension travel so that the tires aren’t rubbing all day. That can lead to a very harsh ride. Again, talk with your Tallahassee wheel professional about all of these things: how you drive, what look you are going for, your budget and what compromises you are willing to make.

At the end of the day, you’re going to be rollin’ out of there with one sweet ride.

At AutoNetTV we love doughnuts. So let’s pretend you have three doughnuts right in front of your for our discussion of upsizing wheels and tires. Hey, don’t eat them now – your going to need them later.

Many people want to accessorize their car – you know, make it theirs. One of the easiest ways to get a custom look is to get some new wheels. There are thousands of wheel designs out there to get you the look you want. And for many, that look includes bigger wheels. It used to be that cars came from the factory with 15 or 16 inch wheels. Now 16, 17 and even 18 inchers are standard. And the factories are offering optional wheel packages up to 20 inches or more.

So let’s talk about what to consider when you want to upsize your wheels. It’s not exactly a do it yourself project, so you need to know a thing or two before you get started. The most important term to know is rolling diameter. The rolling diameter is simply the overall height of your tire. Unless you want to modify your suspension, you’ll want to keep your rolling diameter the same when you upsize your wheels.

Let’s think about those three golden doughnuts in front of you. They’re all about the same size. So if we pretend they’re tires, they would have the same rolling diameter. The doughnut hole is the size of the wheel. Now pretend we’ve made the hole bigger on some. That’s like having a bigger wheel – but the rolling diameter is the same.

It’s important to keep the rolling diameter the same for several reasons. First of all, if the tire is bigger, it might not fit in the wheel well. Next the speedometer, odometer and anti-lock brake system are all calibrated for the factory rolling diameter. In order for your anti-lock brakes to work properly, the rolling diameter must stay within 3% of the factory recommendation. If you ignore that, you run the risk that your anti-lock brakes won’t work properly.

Some cars today have electronically controlled suspension that will be negatively affected by changing the rolling diameter. Let’s think about the doughnuts again. You see, as the size of the wheel gets bigger, the sidewall gets shorter. The tire holds less air, so the sidewalls are made stiffer to compensate.

Low profile tires from top manufacturers use special compounds that give the sidewall the strength it needs without compromising ride quality. As you increase your wheel size, you’ll typically get a slightly wider tire. This means that you have a larger contact patch. The contact patch is part of the tire that contacts the road. Because there’s more rubber on the road, the vehicle will handle better. And braking distances will be shorter. A lot of people with trucks or SUV’s love the extra control.

You do have to watch out that the contact patch isn’t so big that the tires rub in turns or over bumps. What we’re talking about here is fitment. Your tire professional can help you get this right. He’ll install your new wheels, add spacers if needed to make sure your brakes fit inside your new wheels, and get you rolling.

Also, if you drive off-road a lot, you may need a higher profile tire to protect your new rims. And make sure your new tires have the load rating you need if you tow a trailer or haul heavy loads. Again, your tire professional knows how to help.

And don’t forget about tire pressure. If you have larger rims, your new tires will hold less air and they’ll need to run a slightly higher pressure. Forget that and you’ll wear your tires out fast. Finally, get an alignment after you get your new shoes. AutoNetTV wants you to safely have the look you want.

Some of us just love tires. All those little rubber hairs on new tires and the smell is wonderful. We live in a great time for tires. No matter how you drive, where you want to go or the look you’re after; there is a tire for you.

The same is true about wheels. The hardest part is choosing from the thousands of wheels available.

We may not be able to help with that, but we can help you get some things in mind before you consult with your Tallahassee tire professional. Let’s start with function and think about how you drive.

For example, maybe you have a large SUV but you don’t drive off-road, so an off-road tread isn’t important. Also, because you are not out bouncing over rocks in the Florida backcountry, you don’t need a high profile tire to protect your rims. So that means you can probably go with the low-wide look.

If you have a winter season with rain and snow or if you find you need better ice and snow performance, they make great, high-performance snow tires that won’t make it look like you are driving a tractor.

There really are a lot of options for any given vehicle. You will find it very helpful to have a discussion like this with your Tallahassee tire pro when you need new tires. You can find the best solutions for your driving needs and to make improvements in ride or handling.

Picking a wheel that is the same size as what you are now running is pretty simple. But, it gets trickier if you want to upsize. Just get some help when you go bigger. All that tire and wheel still needs to fit in the available space. You do not want your tires to rub when you turn or hit a bump. You also need to make sure your brakes and suspension bits will fit with your wheel of choice. It doesn’t matter how great your car looks if it’s not drivable.

Taller, wider wheels and tires probably weigh more than your stock shoes. And it’s “unsprung” weight – that has a big impact on brake performance. The upsized shoes increase rotational inertia – if you go too big you may need to upgrade your brakes to compensate.

Another possible problem is an inaccurate speedometer. This happens because the number of rotations can change with the new wheels. Fortunately, speedometers and odometers are all controlled by the engine computer; so it is simple to get it reprogrammed and compensate for the bigger tires.

No matter what you are after: low cost, long life, high performance, traction or stunning good looks, your wheel and tire professional at Auto Super-Service Center in Tallahassee, Florida can help you identify your needs and give you a custom fit. With all the options available, you don’t have to compromise. There is a tire out there with your name on it!

One of the most popular vehicle modifications in Florida is custom wheels and tires. Custom wheels help you stand out from the crowd without spending a lot of money, and custom tires can help you fine tune your performance. Not that long ago, new cars came with just one or two tire and wheel options. Now manufacturers are offering more choices and over a third of new vehicle buyers choose custom wheels. That seems to have fueled public demand for custom wheels in all vehicle categories. The available styles, colors and finishes are endless. You’re sure to get the look you want – from sleek and stylish to tough and aggressive.

While custom wheels are largely a matter of taste, custom tires are a matter of function. That is not to say that there are not a lot of cool looking tires out there, it’s just that tires are vital to your safety, so there are some important practical considerations. Let’s look at it in terms of extremes. Think about the environment on a dry race track. High heat, high speed, high cornering forces, hard braking. Then think about a snowy, icy winter that is very cold and slippery. The rubber compound that could withstand the high temperatures and cornering forces on the race track would be very stiff and inflexible in winter conditions. And the rubber compound that provides cold weather flexibility and good bite into ice and snow would rapidly wear out on the race track and wouldn’t be stable at high speeds. Of course the tread design would be greatly different for maintaining traction on a dry race track than it would be for cutting through deep snow.

No one expects any one tire to handle these extremes. So, what we need to do is think about how we drive in Florida and talk to a tire professional about options. There is a tire out there that will meet your driving needs. When you boil it down to the basics, a tire provides traction. The traction is for accelerating, cornering, and for stopping. Once you can identify the conditions you expect to drive in, you can find the tire that will deliver the traction you need.

Tire design and formulation has become very sophisticated. There are fewer compromises in wear, comfort, and performance. You can definitely find a tire that will deliver satisfaction over a range of driving conditions. Now if you live where a tire meeting the severe snow standard is advised, you’ll want to have a set of winter tires during those snowy, icy months.

Let’s go over tire and wheel size. Installing wheels and tires that are the same size as standard is easy. However, many people want to upsize these days and that can get a bit tricky. With the help of your Tallahassee tire professional, you will be able to pick the right tire and wheel combination for the way you drive. For example, if you drive in Florida off-road areas a lot, a low profile tire might not work because there is just not enough cushion for the bumps and rocks.

You’ll want some help to make sure your new tires and wheels fit without rubbing. Your Tallahassee tire pro can also help you know if your engine management computer needs to be reprogrammed so that your speedometer is properly calibrated. A lot of people are tempted to order tires and wheels online but do not realize that some safety systems may be affected. For example, your rolling diameter needs to be within 3% of factory specifications in order for your anti-lock brakes to work properly. Traction and stability control systems can also be adversely affected.

It pays to get professional help when deciding on a wheel size. There has never been a better time to get custom wheels for the look you want. And your tire options are phenomenal. Whether you want a single purpose winter or summer performance tire – or something that can handle a wider range of conditions, you have a tire option for every price range.

When winter approaches, we break out the sweaters, coats, boots and mittens. We want to be ready for winter conditions. Your vehicle needs to be ready for winter as well. The last thing you want is to get stranded out in the cold. You need your vehicle to be safe and reliable. It’s a good idea to get caught up on any neglected maintenance items anytime – but the stakes are higher in the winter.

There are some specific things that we need to do to have our vehicle ready for winter. The most obvious is having the antifreeze checked. If the antifreeze level is too low, it can’t properly protect your engine, radiator and hoses from freezing. If your car does not seem to be making enough heat to keep you warm, your antifreeze level may be low or you could have a thermostat problem. Get it checked out. If you are due for a cooling system service, now is a perfect time to have it done.

In the cold months we always worry about being able to stop in time when it’s slick out. The first thing to remember is to slow down and allow yourself plenty of room to stop. Of course, you want your brakes to be working properly. A thorough brake inspection will reveal if the pads or any other parts need replacing. Check with your service consultant to see if it is time to replace your brake fluid. It accumulates water over time which really messes with your stopping power.

It is a really good idea to have your battery tested. A battery’s cranking power really drops with the temperature. If your battery is weak in the fall, it may not be up to winter. There is nothing like a dead battery in a snow storm.

Which leads us to an emergency kit. You should always have a blanket or something to keep you and your passengers warm if you get stranded. If you will be venturing away from civilization, pack more items such as food and water to help you survive. Keeping at least half a tank of gas is a good precaution if you get stuck and need to run the car to keep warm and it will help keep your gas lines from freezing up.

Winter always makes us think of our windshield wiper blades – usually during that first storm when they aren’t working right. That’s why it’s a really good idea to replace your blades in the fall before the winter storms. If you live where there’s a lot of snow and ice, you might want a special winter blade that resists freezing up. And be sure to have enough windshield washer fluid.

The final thing to consider is your tires. Any tire can lose pressure over time – up to one pound every six or eight weeks. For every 10 degrees the temperature drops you lose another pound of pressure. So if it was 80 degrees outside when you checked your tire pressure two months ago and now it’s 40 degrees out, you could be down 5 pounds of pressure. That’s enough to be a real safety issue and it wastes gas too. You may need special winter tires as well. Your tire professional can help you find the right tire design for your expected road conditions.

If you’re getting winter tires, it is always best to put them on all four wheels. If you are only getting two, have them put on the rear – even if you have a front-wheel drive or four-wheel drive vehicle.

This is a very important safety measure recommended by tire manufacturers. Sliding or fish-tailing on ice and snow is a matter of not having enough traction at the rear end. That is why your newest tires should always be on the rear.